Moves the Bios Data Area header from base-hw to base. Modifies the
base-nova core console that it uses the header as replacement for
the previous BDA bit logic.
Ref #1625
Moreover, be strict when calculating the page-table requirements of
core, which is architecture specific, and declare the virtual memory
requirements of core architecture-wise.
Ref #1588
Instead of organizing page tables within slab blocks and allocating such
blocks dynamically on demand, replace the page table allocator with a
simple, static alternative. The new page table allocator is dimensioned
at compile-time. When a PD runs out of page-tables, we simply flush its
current mappings, and re-use the freed tables. The only exception is
core/kernel that should not produce any page faults. Thereby it has to
be ensured that core has enough page tables to populate it's virtual
memory.
A positive side-effect of this static approach is that the accounting
of memory used for page-tables is now possible again. In the dynamic case
there was no protocol existent that solved the problem of donating memory
to core during a page fault.
Fix#1588
Add a Platform::setup_irq_mode function which enables the IRQ session to
update the trigger mode and polarity of the associated IRQ according to
the session parameters. On ARM this function is a nop.
This change enables the x86_64 platform to support devices which use
arbitrary trigger modes and polarity settings, e.g. AHCI on QEMU and
real hardware.
Fixes#1528.
Placement new can be misleading, as we already overload the new operator
to construct objects via pointers to allocators. To prohibit any problems here,
and to use one consistent approach, we can explicitely construct the object
with the already available 'construct_at' template function.
Ref #1443
The assumption that IRQs in the legacy ISA range are always
edge-triggered is wrong. For the free-for-use IRQs it depends on the
actual device which uses the specific IRQ. Therefore, treat IRQs 9, 10
and 11 as level-triggered.
Perform lazy-initialization of FPU state when it is enabled for the
first time. This assures that the FXSAVE area (including the stored
MXCSR) is always properly setup and initialized to the platform default
values.
Perform all FPU-related setup in the Cpu class' init_fpu function instead of
the general system bring-up assembly code.
Set all required control register 0 and 4 flags according to Intel SDM Vol. 3A,
sections 9.2 and 9.6 instead of only enabling FPU error reporting and OSFXSR.
Physical CPU quota was previously given to a thread on construction only
by directly specifying a percentage of the quota of the according CPU
session. Now, a new thread is given a weighting that can be any value.
The physical counter-value of such a weighting depends on the weightings
of the other threads at the CPU session. Thus, the physical quota of all
threads of a CPU session must be updated when a weighting is added or
removed. This is each time the session creates or destroys a thread.
This commit also adapts the "cpu_quota" test in base-hw accordingly.
Ref #1464
Instead of handing over object ids to the kernel, which has to find them
in object pools then, core can simply use object pointers to reference
kernel objects.
Ref #1443
Instead of having an ID allocator per object class use one global allocator for
all. Thereby artificial limitations for the different object types are
superfluent. Moreover, replace the base-hw specific id allocator implementation
with the generic Bit_allocator, which is also memory saving.
Ref #1443
The port uses the Cortex-A9 private timer for the kernel and an EPIT as
user timer. It was successfully tested on the Wandboard Quad and the CuBox-i
with the signal test. It lacks L2-cache and Trustzone support by now.
Thanks to Praveen Srinivas (IIT Madras, India) and Nikolay Golikov (Ksys Labs
LLC, Russia). This work is partially based on their contributions.
Fix#1467
Do not mask edge-triggered interrupts to avoid losing them while masked,
see Intel 82093AA I/O Advanced Programmable Interrupt Controller
(IOAPIC) specification, section 3.4.2, "Interrupt Mask":
"When this bit is 1, the interrupt signal is masked. Edge-sensitive
interrupts signaled on a masked interrupt pin are ignored (i.e., not
delivered or held pending)"
Or to quote Linus Torvalds on the subject:
"Now, edge-triggered interrupts are a _lot_ harder to mask, because the
Intel APIC is an unbelievable piece of sh*t, and has the edge-detect
logic _before_ the mask logic, so if a edge happens _while_ the device
is masked, you'll never ever see the edge ever again (unmasking will not
cause a new edge, so you simply lost the interrupt)."
So when you "mask" an edge-triggered IRQ, you can't really mask it at
all, because if you did that, you'd lose it forever if the IRQ comes in
while you masked it. Instead, we're supposed to leave it active, and set
a flag, and IF the IRQ comes in, we just remember it, and mask it at
that point instead, and then on unmasking, we have to replay it by
sending a self-IPI." [1]
[1] - http://yarchive.net/comp/linux/edge_triggered_interrupts.html
Ref #1448
* Enable the use of the FXSAVE and FXRSTOR instructions, see Intel SDM
Vol. 3C, section 2.5.
* The state of the x87 floating point unit (FPU) is loaded and saved on
demand.
* Make the cr0 control register accessible in the Cpu class. This is in
preparation of the upcoming FPU management.
* Access to the FPU is disabled by setting the Task Switch flag in the cr0
register.
* Access to the FPU is enabled by clearing the Task Switch flag in the cr0
register.
* Implement FPU initialization
* Add is_fpu_enabled helper function
* Add pointer to CPU lazy state to CPU class
* Init FPU when finishing kernel initialization
* Add function to retry FPU instruction:
Similar to the ARM mechanism to retry undefined instructions, implement a
function for retrying an FPU instruction. If a floating-point instruction
causes an #NM exception due to the FPU being disabled, it can be retried
after the correct FPU state is restored, saving the current state and
enabling the FPU in the process.
* Disable FPU when switching to different user context:
This enables lazy save/restore of the FPU since trying to execute a
floating point instruction when the FPU is disabled will cause a #NM
exception.
* Declare constant for #NM exception
* Retry FPU instruction on #NM exception
* Assure alignment of FXSAVE area:
The FXSAVE area is 512-byte memory region that must be 16-byte aligned. As
it turns out the alignment attribute is not honored in all cases so add a
workaround to assure the alignment constraint is met by manually rounding
the start of the FXSAVE area to the next 16-byte boundary if necessary.
The LAPIC timer is programmed in one-shot mode with vector 32
(Board::TIMER_VECTOR_KERNEL). The timer frequency is measured using PIT
channel 2 as reference (50ms delay).
Disable PIT timer channel 0 since BIOS programs it to fire periodically.
This avoids potential spurious timer interrupts.
The implementation initializes the Local APIC (LAPIC) of CPU 0 in xapic
mode (mmio register access) and uses the I/O APIC to remap, mask and
unmask hardware IRQs. The remapping offset of IRQs is 48.
Also initialize the legacy PIC and mask all interrupts in order to
disable it.
For more information about LAPIC and I/O APIC see Intel SDM Vol. 3A,
chapter 10 and the Intel 82093AA I/O Advanced Programmable Interrupt
Controller (IOAPIC) specification
Set bit 9 in the RFLAGS register of user CPU context to enable
interrupts on kernel- to usermode switch.
The location in memory is arbitrary but we use the same address as the
ARM architecture. Adjust references to virtual addresses in the mode
transition pages to cope with 64-bit values.
Use parameter instead of class member variable because it would get
stored into the mtc region otherwise. In a further iteration only the
actual IDT should be saved into the mtc, not the complete class
instance. Currently the class instance size is equal to the IDT table
size.
The class provides the load() function which reloads the GDTR with the
GDT address in the mtc region. This is needed to make the segments
accessible to non-core threads.
Make the _gdt_start label global to use it in the call to
_virt_mtc_addr().
Use the _mt_tss label and the placement new operator to create the
Tss class instance in the mtc region. Update the hard-coded
TSS base address to use the virtual mtc address.
