This commit enables multi-processing for all Cortex A9 SoCs we currently
support. Moreover, it thereby enables the L2 cache for i.MX6 that was not
enabled until now. However, the QEMU variants hw_pbxa9 and hw_zynq still
only use 1 core, because the busy cpu synchronization used when initializing
multiple Cortex A9 cores leads to horrible boot times on QEMU.
During this work the CPU initialization in general was reworked. From now
on lots of hardware specifics were put into the 'spec' specific files, some
generic hook functions and abstractions thereby were eliminated. This
results to more lean implementations for instance on non-SMP platforms,
or in the x86 case where cache maintainance is a non-issue.
Due to the fact that memory/cache coherency and SMP are closely coupled
on ARM Cortex A9 this commit combines so different aspects.
Fix#1312Fix#1807
This commit separates certain SMP aspects into 'spec/smp' subdirectories.
Thereby it simplifies non-SMP implementations again, where no locking
and several platform specific maintainance operations are not needed.
Moreover, it moves several platform specifics to appropriated places,
removes dead code from x86, and starts to turn global static pointers
into references that are handed over.
Other platforms implement Kernel::Cpu_context stuff in
kernel/cpu_context.cc. On x86_64, it was implemented in
kernel/thread.cc. The commit fixes this inconsistency to the other
platforms.
Ref #1652
The distinction between Kernel::Thread and Kernel::Thread_base is
unnecessary as currently all Hw platforms would have the same content in
the latter class. Thus I've merged Kernel::Thread_base into
Kernel::Thread. Thereby, Kernel::Thread_event can be moved to
kernel/thread.h.
Ref #1652
Move Platform::setup_irq_mode function from x86 platform_support.cc to
x86_64 specific file. This will enable the upcoming x86_64_muen platform
to provide a separate implementation.
Move the _core_only_mmio_regions function to the
x86_64/platform_support.cc file. This is required to make it overridable
for other platforms deriving from x86.
Perform all FPU-related setup in the Cpu class' init_fpu function instead of
the general system bring-up assembly code.
Set all required control register 0 and 4 flags according to Intel SDM Vol. 3A,
sections 9.2 and 9.6 instead of only enabling FPU error reporting and OSFXSR.
* Enable the use of the FXSAVE and FXRSTOR instructions, see Intel SDM
Vol. 3C, section 2.5.
* The state of the x87 floating point unit (FPU) is loaded and saved on
demand.
* Make the cr0 control register accessible in the Cpu class. This is in
preparation of the upcoming FPU management.
* Access to the FPU is disabled by setting the Task Switch flag in the cr0
register.
* Access to the FPU is enabled by clearing the Task Switch flag in the cr0
register.
* Implement FPU initialization
* Add is_fpu_enabled helper function
* Add pointer to CPU lazy state to CPU class
* Init FPU when finishing kernel initialization
* Add function to retry FPU instruction:
Similar to the ARM mechanism to retry undefined instructions, implement a
function for retrying an FPU instruction. If a floating-point instruction
causes an #NM exception due to the FPU being disabled, it can be retried
after the correct FPU state is restored, saving the current state and
enabling the FPU in the process.
* Disable FPU when switching to different user context:
This enables lazy save/restore of the FPU since trying to execute a
floating point instruction when the FPU is disabled will cause a #NM
exception.
* Declare constant for #NM exception
* Retry FPU instruction on #NM exception
* Assure alignment of FXSAVE area:
The FXSAVE area is 512-byte memory region that must be 16-byte aligned. As
it turns out the alignment attribute is not honored in all cases so add a
workaround to assure the alignment constraint is met by manually rounding
the start of the FXSAVE area to the next 16-byte boundary if necessary.
The implementation initializes the Local APIC (LAPIC) of CPU 0 in xapic
mode (mmio register access) and uses the I/O APIC to remap, mask and
unmask hardware IRQs. The remapping offset of IRQs is 48.
Also initialize the legacy PIC and mask all interrupts in order to
disable it.
For more information about LAPIC and I/O APIC see Intel SDM Vol. 3A,
chapter 10 and the Intel 82093AA I/O Advanced Programmable Interrupt
Controller (IOAPIC) specification
Set bit 9 in the RFLAGS register of user CPU context to enable
interrupts on kernel- to usermode switch.
Make the local APIC accessible via its MMIO region by adding a 2 MB
large page mapping at 0xfee00000 with memory type UC.
Note: The mapping is added to the initial page tables to make the APIC
usable prior to the activation of core's page tables, e.g. in the
constructor of the timer class.
The location in memory is arbitrary but we use the same address as the
ARM architecture. Adjust references to virtual addresses in the mode
transition pages to cope with 64-bit values.
The interrupt stack must reside in the mtc region in order to use it for
non-core threads. The size of the stack is set to 56 bytes in order to
hold the interrupt stack frame plus the additional vector number that is
pushed onto the stack by the ISR.
Call the _virt_mtc_addr function with the _mt_isrs label to calculate
the ISR base address in Idt::setup. Again, assume the address to be
below 0x10000.
Use parameter instead of class member variable because it would get
stored into the mtc region otherwise. In a further iteration only the
actual IDT should be saved into the mtc, not the complete class
instance. Currently the class instance size is equal to the IDT table
size.
The class provides the load() function which reloads the GDTR with the
GDT address in the mtc region. This is needed to make the segments
accessible to non-core threads.
Make the _gdt_start label global to use it in the call to
_virt_mtc_addr().
Use the _mt_tss label and the placement new operator to create the
Tss class instance in the mtc region. Update the hard-coded
TSS base address to use the virtual mtc address.
