Older ARM processors like ARMv6, or Cortex A8 need to write back changes
of the page-tables to physical ram because the MMU does not use the cache.
This naturally needs to be done not only when adding a mapping,
but on removal too.
Fix#3715
This patch adds support for booting base-hw kernel on qemu-arm virt
machines. The arm_virt machine has 2GB of RAM, 2 Cortex A15 cores and
uses GICv2 interrupt controller. The arm_64_virt machine also has 2GB of
RAM, but has 4 Cortex A53 cores and uses GICv3. Both machines use PSCI
to boot additional CPU cores.
Fixes#3673
So far this only exposes two functions allowing the code to turn on
additional CPUs. There is much more functionality defined by PSCI spec
but so far its not needed by Genode.
Fixes#3672
This commit fixes the following issues regarding cache maintainance
under ARM:
* read out I-, and D-cache line size at runtime and use the correct one
* remove 'update_data_region' call from unprivileged syscalls
* rename 'update_instr_region' syscall to 'cache_coherent_region' to
reflect what it doing, namely make I-, and D-cache coherent
* restrict 'cache_coherent_region' syscall to one page at a time
* lookup the region given in a 'cache_coherent_region' syscall in the
page-table of the PD to prevent machine exceptions in the kernel
* only clean D-cache lines, do not invalidate them when pages where
added on Cortex-A8 and ARMv6 (MMU sees phys. memory here)
* remove unused code relicts of cache maintainance
In addition it introduces per architecture memory clearance functions
used by core, when preparing new dataspaces. Thereby, it optimizes:
* on ARMv7 using per-word assignments
* on ARMv8 using cacheline zeroing
* on x86_64 using 'rept stosq' assembler instruction
Fix#3685
The mutex class is more restrictive in usage compared to
Genode::Lock.
- At initialiation time it is ever unlocked.
- No thread is permitted to lock twice. Warn about it
in case it happens.
- Only the lock onwer is permitted to unlock the mutex.
Warn about it and don't unlock the mutex in case it happens.
Issue #3612
We cannot count on the correct initialization of the diagnostic register
of the secondary cores. But the boot core gets initialized by the bootchain,
so we can copy over those values.
Fix#3639
Whether an SoC has the multiprocessing extensions can be read out
from the identification registers, and does not need to be specified
in each board header.
Ref #3445
On x86 the CPU count is determined through ACPI's MADT by counting the
local APICs reported there. Some platforms report more APICs
than there are actual CPUs. These might be physically disabled CPUs.
Therefore, a check if the LAPIC is actually physically enabled in
hardware fixes this issue.
Thanks to Alex Boettcher
fixes#3376
The patch adjust the code of the base, base-<kernel>, and os repository.
To adapt existing components to fix violations of the best practices
suggested by "Effective C++" as reported by the -Weffc++ compiler
argument. The changes follow the patterns outlined below:
* A class with virtual functions can no longer publicly inherit base
classed without a vtable. The inherited object may either be moved
to a member variable, or inherited privately. The latter would be
used for classes that inherit 'List::Element' or 'Avl_node'. In order
to enable the 'List' and 'Avl_tree' to access the meta data, the
'List' must become a friend.
* Instead of adding a virtual destructor to abstract base classes,
we inherit the new 'Interface' class, which contains a virtual
destructor. This way, single-line abstract base classes can stay
as compact as they are now. The 'Interface' utility resides in
base/include/util/interface.h.
* With the new warnings enabled, all member variables must be explicitly
initialized. Basic types may be initialized with '='. All other types
are initialized with braces '{ ... }' or as class initializers. If
basic types and non-basic types appear in a row, it is nice to only
use the brace syntax (also for basic types) and align the braces.
* If a class contains pointers as members, it must now also provide a
copy constructor and assignment operator. In the most cases, one
would make them private, effectively disallowing the objects to be
copied. Unfortunately, this warning cannot be fixed be inheriting
our existing 'Noncopyable' class (the compiler fails to detect that
the inheriting class cannot be copied and still gives the error).
For now, we have to manually add declarations for both the copy
constructor and assignment operator as private class members. Those
declarations should be prepended with a comment like this:
/*
* Noncopyable
*/
Thread(Thread const &);
Thread &operator = (Thread const &);
In the future, we should revisit these places and try to replace
the pointers with references. In the presence of at least one
reference member, the compiler would no longer implicitly generate
a copy constructor. So we could remove the manual declaration.
Issue #465
* Instead of always re-load page-tables when a thread context is switched
only do this when another user PD's thread is the next target,
core-threads are always executed within the last PD's page-table set
* remove the concept of the mode transition
* instead map the exception vector once in bootstrap code into kernel's
memory segment
* when a new page directory is constructed for a user PD, copy over the
top-level kernel segment entries on RISCV and X86, on ARM we use a designated
page directory register for the kernel segment
* transfer the current CPU id from bootstrap to core/kernel in a register
to ease first stack address calculation
* align cpu context member of threads and vms, because of x86 constraints
regarding the stack-pointer loading
* introduce Align_at template for members with alignment constraints
* let the x86 hardware do part of the context saving in ISS, by passing
the thread context into the TSS before leaving to user-land
* use one exception vector for all ARM platforms including Arm_v6
Fix#2091
* introduces central memory map for core/kernel
* on 32-bit platforms the kernel/core starts at 0x80000000
* on 64-bit platforms the kernel/core starts at 0xffffffc000000000
* mark kernel/core mappings as global ones (tagged TLB)
* move the exception vector to begin of core's binary,
thereby bootstrap knows from where to map it appropriately
* do not map boot modules into core anymore
* constrain core's virtual heap memory area
* differentiate in between user's and core's main thread's UTCB,
which now resides inside the kernel segment
Ref #2091
When running core as the kernel inside every component, a separate
stack area for core is needed that is different from the user-land
component's one.
Ref #2091
The recently implemented capability resource trading scheme unfortunately
broke the automated capability memory upgrade mechanism needed by base-hw
kernel/core. This commit splits the capability memory upgrade mechanism
from the PD session ram_quota upgrade, and moves that functionality
into a separate Pd_session::Native_pd interface.
Ref #2398
This patch mirrors the accounting and trading scheme that Genode employs
for physical memory to the accounting of capability allocations.
Capability quotas must now be explicitly assigned to subsystems by
specifying a 'caps=<amount>' attribute to init's start nodes.
Analogously to RAM quotas, cap quotas can be traded between clients and
servers as part of the session protocol. The capability budget of each
component is maintained by the component's corresponding PD session at
core.
At the current stage, the accounting is applied to RPC capabilities,
signal-context capabilities, and dataspace capabilities. Capabilities
that are dynamically allocated via core's CPU and TRACE service are not
yet covered. Also, the capabilities allocated by resource multiplexers
outside of core (like nitpicker) must be accounted by the respective
servers, which is not covered yet.
If a component runs out of capabilities, core's PD service prints a
warning to the log. To observe the consumption of capabilities per
component in detail, the PD service is equipped with a diagnostic
mode, which can be enabled via the 'diag' attribute in the target
node of init's routing rules. E.g., the following route enables the
diagnostic mode for the PD session of the "timer" component:
<default-route>
<service name="PD" unscoped_label="timer">
<parent diag="yes"/>
</service>
...
</default-route>
For subsystems based on a sub-init instance, init can be configured
to report the capability-quota information of its subsystems by
adding the attribute 'child_caps="yes"' to init's '<report>'
config node. Init's own capability quota can be reported by adding
the attribute 'init_caps="yes"'.
Fixes#2398
This cleans up the syscalls that are mainly used to control the
scheduling readiness of a thread. The different use cases and
requirements were somehow mixed together in the previous interface. The
new syscall set is:
1) pause_thread and resume_thread
They don't affect the state of the thread (IPC, signalling, etc.) but
merely decide wether the thread is allowed for scheduling or not, the
so-called pause state. The pause state is orthogonal to the thread state
and masks it when it comes to scheduling. In contrast to the stopped
state, which is described in "stop_thread and restart_thread", the
thread state and the UTCB content of a thread may change while in the
paused state. However, the register state of a thread doesn't change
while paused. The "pause" and "resume" syscalls are both core-restricted
and may target any thread. They are used as back end for the CPU session
calls "pause" and "resume". The "pause/resume" feature is made for
applications like the GDB monitor that transparently want to stop and
continue the execution of a thread no matter what state the thread is
in.
2) stop_thread and restart_thread
The stop syscall can only be used on a thread in the non-blocking
("active") thread state. The thread then switches to the "stopped"
thread state in wich it explicitely waits for a restart. The restart
syscall can only be used on a thread in the "stopped" or the "active"
thread state. The thread then switches back to the "active" thread state
and the syscall returns whether the thread was stopped. Both syscalls
are not core-restricted. "Stop" always targets the calling thread while
"restart" may target any thread in the same PD as the caller. Thread
state and UTCB content of a thread don't change while in the stopped
state. The "stop/restart" feature is used when an active thread wants to
wait for an event that is not known to the kernel. Actually the syscalls
are used when waiting for locks and on thread exit.
3) cancel_thread_blocking
Does cleanly cancel a cancelable blocking thread state (IPC, signalling,
stopped). The thread whose blocking was cancelled goes back to the
"active" thread state. It may receive a syscall return value that
reflects the cancellation. This syscall doesn't affect the pause state
of the thread which means that it may still not get scheduled. The
syscall is core-restricted and may target any thread.
4) yield_thread
Does its best that a thread is scheduled as few as possible in the
current scheduling super-period without touching the thread or pause
state. In the next superperiod, however, the thread is scheduled
"normal" again. The syscall is not core-restricted and always targets
the caller.
Fixes#2104
This is a redesign of the root and parent interfaces to eliminate
blocking RPC calls.
- New session representation at the parent (base/session_state.h)
- base-internal root proxy mechanism as migration path
- Redesign of base/service.h
- Removes ancient 'Connection::KEEP_OPEN' feature
- Interface change of 'Child', 'Child_policy', 'Slave', 'Slave_policy'
- New 'Slave::Connection'
- Changed child-construction procedure to be compatible with the
non-blocking parent interface and to be easier to use
- The child's initial LOG session, its binary ROM session, and the
linker ROM session have become part of the child's envirenment.
- Session upgrading must now be performed via 'env.upgrade' instead
of performing a sole RPC call the parent. To make RAM upgrades
easier, the 'Connection' provides a new 'upgrade_ram' method.
Issue #2120
This patch establishes the sole use of generic headers across all
kernels. The common 'native_capability.h' is based on the version of
base-sel4. All traditional L4 kernels and Linux use the same
implementation of the capability-lifetime management. On base-hw, NOVA,
Fiasco.OC, and seL4, custom implementations (based on their original
mechanisms) are used, with the potential to unify them further in the
future.
This change achieves binary compatibility of dynamically linked programs
across all kernels.
Furthermore, the patch introduces a Native_capability::print method,
which allows the easy output of the kernel-specific capability
representation using the base/log.h API.
Issue #1993
