109 lines
3.5 KiB
Nix
109 lines
3.5 KiB
Nix
{ config, lib, pkgs, ... }:
|
|
|
|
{
|
|
imports = [
|
|
./hardware-configuration.nix
|
|
];
|
|
|
|
c3d2 = {
|
|
hq.interface = "eth0";
|
|
hq.statistics.enable = true;
|
|
k-ot.enable = true;
|
|
};
|
|
|
|
boot = {
|
|
growPartition = true;
|
|
kernelParams = [ "console=tty0" ];
|
|
loader.grub.enable = false;
|
|
loader.efi.canTouchEfiVariables = true;
|
|
supportedFilesystems = lib.mkForce [ "vfat" "ext4" ];
|
|
tmp.useTmpfs = true;
|
|
};
|
|
|
|
hardware = {
|
|
bluetooth.enable = true;
|
|
deviceTree.enable = true;
|
|
};
|
|
|
|
nix.settings = {
|
|
cores = 2;
|
|
max-jobs = 1;
|
|
};
|
|
|
|
nixpkgs.config.packageOverrides = pkgs: {
|
|
makeModulesClosure = x:
|
|
# prevent kernel install fail due to missing modules
|
|
pkgs.makeModulesClosure (x // { allowMissing = true; });
|
|
};
|
|
|
|
networking = {
|
|
domain = "hq.c3d2.de";
|
|
hostName = "pulsebert";
|
|
useDHCP = false;
|
|
interfaces.eth0.useDHCP = true;
|
|
};
|
|
|
|
# https://github.com/dump-dvb/nix-config/blob/310ceedca5ab2d5c22070bd73c603926b6100a74/hardware/configuration-rpi-3b.nix#L16
|
|
sdImage = lib.mkForce {
|
|
populateFirmwareCommands =
|
|
let
|
|
configTxt = pkgs.writeText "config.txt" ''
|
|
[pi3]
|
|
kernel=u-boot-rpi3.bin
|
|
hdmi_force_hotplug=1
|
|
[pi02]
|
|
kernel=u-boot-rpi3.bin
|
|
[pi4]
|
|
kernel=u-boot-rpi4.bin
|
|
enable_gic=1
|
|
armstub=armstub8-gic.bin
|
|
# Otherwise the resolution will be weird in most cases, compared to
|
|
# what the pi3 firmware does by default.
|
|
disable_overscan=1
|
|
# Supported in newer board revisions
|
|
arm_boost=1
|
|
[cm4]
|
|
# Enable host mode on the 2711 built-in XHCI USB controller.
|
|
# This line should be removed if the legacy DWC2 controller is required
|
|
# (e.g. for USB device mode) or if USB support is not required.
|
|
otg_mode=1
|
|
[all]
|
|
# Boot in 64-bit mode.
|
|
arm_64bit=1
|
|
# U-Boot needs this to work, regardless of whether UART is actually used or not.
|
|
# Look in arch/arm/mach-bcm283x/Kconfig in the U-Boot tree to see if this is still
|
|
# a requirement in the future.
|
|
enable_uart=1
|
|
# Prevent the firmware from smashing the framebuffer setup done by the mainline kernel
|
|
# when attempting to show low-voltage or overtemperature warnings.
|
|
avoid_warnings=1
|
|
'';
|
|
in
|
|
''
|
|
(cd ${pkgs.raspberrypifw}/share/raspberrypi/boot && cp bootcode.bin fixup*.dat start*.elf $NIX_BUILD_TOP/firmware/)
|
|
# Add the config
|
|
cp ${configTxt} firmware/config.txt
|
|
# Add pi3 specific files
|
|
cp ${pkgs.ubootRaspberryPi3_64bit}/u-boot.bin firmware/u-boot-rpi3.bin
|
|
# Add pi4 specific files
|
|
cp ${pkgs.ubootRaspberryPi4_64bit}/u-boot.bin firmware/u-boot-rpi4.bin
|
|
cp ${pkgs.raspberrypi-armstubs}/armstub8-gic.bin firmware/armstub8-gic.bin
|
|
cp ${pkgs.raspberrypifw}/share/raspberrypi/boot/bcm2711-rpi-4-b.dtb firmware/
|
|
cp ${pkgs.raspberrypifw}/share/raspberrypi/boot/bcm2711-rpi-400.dtb firmware/
|
|
cp ${pkgs.raspberrypifw}/share/raspberrypi/boot/bcm2711-rpi-cm4.dtb firmware/
|
|
cp ${pkgs.raspberrypifw}/share/raspberrypi/boot/bcm2711-rpi-cm4s.dtb firmware/
|
|
'';
|
|
populateRootCommands = ''
|
|
mkdir -p ./files/boot
|
|
${config.boot.loader.generic-extlinux-compatible.populateCmd} -c ${config.system.build.toplevel} -d ./files/boot
|
|
'';
|
|
};
|
|
|
|
security.sudo = {
|
|
enable = true;
|
|
wheelNeedsPassword = false;
|
|
};
|
|
|
|
system.stateVersion = "22.11";
|
|
}
|