The Ethernet payload may be followed by padding of variable length and
the FCS (Frame Check Sequence). Thus, we should consider the value
"Ethernet-frame size minus Ethernet-header size" to be only the maximum
size of the encapsulated IP packet. But until now, we considered it to
be also the actual size of the encapsulated IP packet. This commit fixes
the problem for all affected components of the Genode base-repository.
Fixes#2775
This reduces the redundant implementations of checksum calculation to
one generic implementation, makes the checksum interface conform over
all protocols, and brings performance optimizations. For instance,
the checksum is now calculated directly in big endian which saves us
most of the previously done byte-re-ordering.
Issue #2775
Replace packet method 'T *data' by the new methods 'T &reinterpret_data'
for parsing or modifying existing sub-protocol packets and 'T
&construct_at_data' for composing a new sub-protocol packet. This has
the advantage that, when composing a new packet, the default constructor
that zero-fills the packet is always called first.
Fixes#2751
This commit changes the 'Input::Event' type to be more safe and to
deliver symbolic character information along with press events.
Issue #2761Fixes#2786
On the Raspberry PI, the 2 seconds of round time in the polling test
were not sufficient to reach the goal of at least 1000 successful polls.
Thus, the commit sets the round time to 2.5 seconds which doesn't hurt to
much but allows the RPI to just make it.
Fixes#2779
This patch largely reverts the feature of selecting parts of input nodes
from within the output node (as originally introduced by commit
7263cae5a18b4f1f2293d031f9bafcf05ba51146). The selection of content
should be consistently performed by input nodes instead. The principle
ability of copying input nodes verbatim into the output stays available.
Issue #2691
The new 'attribute' and 'value' attributes of input nodes
can be used to select input sub nodes that match the presence and value
of the specified attribute.
Issue #2691
The 'stat' method is called for all paths, not just the specific file
system node of the ROM module. The ROM update is needed only in the
latter case.
Otherwise, when always updating the ROM on stat, stat calls on the VFS
become very expensive in the presence of a mounted ROM module if the ROM
is obtained from fs_rom (which re-watches the file and all its
individual path elements whenever the 'update' RPC function is called).
Reduce the size and forward compatibility of VFS file-system
constructors by passing an object holding accessors for 'Genode::Env',
'Genode::Allocator', response handlers, and the root file-system.
Fix#2742
When working with GPIO interrupts on i.MX6SX for Ethernet PHYs
it became obvious that the GPIO driver repeatedly receives interrupts
for the same event, because it acknowledges the interrupt before a
client has handled the event.
Ref #2750
This driver component provides support for using consumer NVMe storage
devices, i.e. it omits name space managment and will always use the
first name space, on Genode. For now it defaults to a reasonable low
configuration:
- 1 I/O queue (completion/submission tuple)
- 128 entries in the I/O queue
- 4096 as the only I/O transaction memory page size
Fixes#2747.
The 'default' attribute is useful to change the default value for those
protocol attributes that are not explicitely set in the configuration of
the component.
Issue #2738
Each supported protocol now has an attribute with the name of the protocol in
the config tag. Each of these attributes accepts one of four possible values:
* no - do not print out this protocol
* name - print only the protocol name
* default - print a short summary of the most important header values
* all - print all available header values
Example:
! <config eth="name"
! arp="all"
! ipv4="default"
! dhcp="no"
! icmp="all"
! udp="no"
! tcp="default"
! ... />
Corresponding output example:
! ETH IPV4 10.0.2.212 > 10.0.2.55 time 7158 ms (Δ 11 ms)
! ETH IPV4 10.0.2.55 > 10.0.2.201 TCP 80 > 49154 flags ' time 6976 ms (Δ 5 ms)
! ETH ARP hw 1 prot 2048 hwsz 6 protsz 4 op 1 srcmac 02:02:02:02:02:01 srcip 10.0.2.212 dstmac 00:00:00:00:00:00 dstip 10.0.2.55 time 7074 ms (Δ 98 ms)
Issue #2738
Nitpicker's 'Session:focus' call used to trigger a one-off focus change
at call time. This focus change did not pass the same code paths as a
focus change triggered by a "focus" ROM update, which led to
inconsistencies.
This patch changes the implementation of 'Session::focus' such that the
relationship of the caller and the focused session is preserved after
call time. Whenever the calling session is focused in the future, the
specified session will receive the focus instead. So 'Session::focus'
represents no longer a single operation but propagates the information
about the inter-session relationship. This information is taken into
account whenever the focus is evaluated regardless of how the change is
triggered.
This makes the focus handling in scenarios like the window manager more
robust.
Issue #2746
Relative motion events with a motion vector of (0,0) should not exists.
They cause jittery movements of nitpicker's pointer position. This
patch filters out such events.
The 'ping' component continuously sends ICMP Echo requests to a given IP host
and waits for the corresponding ICMP Echo replies. For each successfull ICMP
Echo handshake it prints a short statistic. By now, it can be used only with a
static IP configuration. The size of the ICMP data field can be configured. It
gets filled with the letters of the alphabet ('a' to 'z') repeatedly.
Issue #2732
Originally, the timeout framework caused deadlocks when acquiring the same
lock from different timeout handlers. This use case is now tested in the
timeout test.
Fixes#2704
To handle all pending timeouts in the context of scheduling a timeout
was only necessary because the Timeout framework once made use of the
Alarm framework. The method Alarm_scheduler::schedule_absolute took an
absolute deadline as argument and we couldn't change this beause the
Alarm framework was also used without the Timeout framework. We had to
calculate this absolute deadline with the now time of the Timeout
framework but the Alarm framework has its own now time that is always a
bit behind the one of the Timeout framework. This lead to bad decisisons
when finding the right position for the new timeout. Now, we can call
schedule_absolute with a relative duration and thereby fix the problem.
When we schedule an absolute timeout without considering the small time
difference, the end-time for the timeout that is calculated using the
local time value is also smaller than the expected end-time. This can
also lead to directly triggering timeouts that should have triggered
with a certain delay.
As it is not trivial to update the local time value while scheduling a
timeout _without_ calling other timeout handlers, we simply raise the
duration of the new timeout by the age of the local time value.
Issue #2704
This fixes the problem that large timeouts, when rescheduled, are interpreted
to be from the last now_period instead of, what would be right, the next
now_period. This occured if there were multiple pending alarms at the head of
the queue and the reschedule of the first one was done with the other outdated
deadlines still in place.
Issue #2704
Instead of taking the absolute deadline of a timeout as argument from
outside (where it is calculated with a freshly requested now time), we
now take a relative duration as argument and calculate the deadline with
the scheduler-internal now time (which can be a little bit outdated).
This enables us to schedule timeouts without updating the internal now time
and thereby handle all pending timeouts.
Issue #2704
