This patch enables the use of the VFS from VFS plugins by passing a
reference of the root directory to the constructors of file-system
instances. Since it changes the signature of 'Vfs::Dir_file_system',
any code that uses the VFS directly requires an adaptation.
Fixes#2701
If the remote DNS server address value of a DHCP server changes, the affected
interfaces do a link down/up to inform all DHCP clients that they should
re-request their DHCP info.
Issue #2730
The dns_server_from attribute of the dhcp-server tag has effect only if
the dns_server attribute of the same tag is not set. If this is the
case, the dns_server_from attribute states the domain from whose IP
config to take the DNS server address. This is useful, for instance, if
the stated domain receives the address of a local DNS server via DHCP.
Whenever the IP config of the stated domain becomes invalid, the DHCP
server switches to a mode where it drops all requests unanswered until
the IP config becomes valid again.
Issue #2730
Until now, the DHCP server of a domain was re-constructed each time the
IP config changed. This is not necessary as a domain that acts as DHCP
server must have a static IP config as it would be senseless to act as
DHCP server and client at the same time. Now, a configured DHCP server
is constructed only when the Domain gets constructed and stays alive
until the domain gets destructed. Furthermore, we now throw Domain::Invalid
if there is no static IP config plus a DHCP server configured. However, by
now, this exception is not caught as it is not trivial to destruct the
domain at this point.
Issue #2730
The Interface constructor previously tried to attach to a domain. This
might include sending a DHCP request to get the domain a valid IP config.
But in order to achieve this, the constructor used a pure virtual method
of Interface which crashes due to the unfinished vtable. To fix this bug,
the attach attempt was moved to a new Interface::init method.
Issue #2730
Instead of Pointer<T>::set use assignment operator with implicit constructor
from T-reference. Instead of Pointer<T>::unset use assignment operator with
Pointer<T>(). Instead of Pointer<T>::deref provide () operator.
Issue #2730
The router reacts as follows to a configuration change:
1) Construct new internal configuration representation (the old one stays
in place to be able to do comparisons in the following steps)
2) Iterate through all user-dependent objects (interfaces, link states, ARP
information, DHCP information) and re-check which remain valid with the
new configuration and which must be dismissed.
3) Adapt the objects that remain valid to the new configuration (re-write
references) and remove or detach the dismissed objects.
4) Do a link state DOWN at each interface and a link state UP at each
interface that remains attached to a domain.
5) Replace the old internal configuration representation with the new one
This way, the router keeps as much user dependent states as possible
while going through a configuration change. Thus, overwriting the old
configuration with an exact copy of itself is (almost) transparent to
clients of the router. Almost, because there are things the router must
do on every configuration handling, like re-scheduling the expiration
timeouts of links.
Ref #2670
The for_each method of the List wrapper remembers the next list item
before calling the functor on the current one, so, the current one can
be destroyed during the functor.
Ref #2670
Clients can connect at any time to the NIC router. The interfaces (sessions)
get attached to the appropriate domain as soon as it appears. This implies
that interfaces can also be detached from a domain without beeing destructed
when the domain disappears. All user dependent states of an interface such as
the link states, DHCP allocations and ARP information get lost when the
interface gets detached.
Ref #2670
This separates the decision wether to log the received and sent packets
from the 'verbose' attribute. This information is now only logged if
'verbose_packets' is switched on. If 'verbose' is switched on, only
routing decisions and optional hints are printed.
Ref #2670
Switch port I/O based PCI config space access to memory-mapped IO. The
base address of the PCI configuration space is acquired by mapping the
ACPI ROM and reading the first <bdf> node. An exception is thrown if the
first <bdf> node is not for PCI domain zero or if multiple <bdf> nodes
exist. This is to reduce complexity and also because multiple PCI
domains are rare.
The PCI configuration space is accessed via I/O mem dataspace which is
created in the platform_drv root and then passed on to the PCI session,
device components and finally to the actual PCI config access instances.
The memory access code is implemented in a way to make it work with Muen
subject monitor (SM) device emulation and also general x86 targets. On
Muen, the simplified device emulation code (which works also for Linux)
always returns 0xffff in EAX to indicate a non-existing device.
Therefore, EAX is enforced in the assembly templates.
Fixes#2547
This patch adds a safety check to nit_fb to ensures that nit_fb never
runs out of RAM. Should the available RAM not suffice for resizing the
virtual framebuffer to a new mode, it keeps the current mode.
This patch removes the notion of partial writes from the file-system
servers. Since write operations are asynchronously submitted, they are
expected to succeed completely, except for I/O errors. I/O errors are
propagated with the write acknowledgement but those are usually handled
out of band at the client side. Partial writes must never occur because
they would go undetected by clients, which usually don't wait for the
completion of each single write operation.
Until now, most file-system servers returned the number of written bytes
in the acknowledgement packet. If a server managed to write a part of
the request only, it issued the acknowledgement immediately where it
should have cared about writing the remaining part first.
The patch detects such misbehaving server-side code. If partial writes
unexpectedly occur, it prints a message and leaves the corresponding
request unacknowdleged.
Issue #2672
File_system clients may now watch files and directories for changes by
opening a 'Watch_handle' rather than submitting a 'CONTENT_CHANGED'
packet to the server. When a change happens at a node with an open
Watch_handle a CONTENT_CHANGED packet will be sent from the server to
the client. This serializes registration with other handle operations
and separates I/O handle state from notification handle state.
Test at run/fs_rom_update.
Ref #1934
Catch out of RAM and capability exceptions and return error values.
Abort opening a composite directory at Dir_file_system where an
opendir call on any child file-system returns an OUT_OF_RAM or
OUT_OF_CAPS error.
Ref #2642
This change enables the use of negative values for the 'initial_width'
and 'initial_height' attributes to specify values that are relative to
the screen size. This is consistent with the meaning of the 'width' and
'height' attributes.
The new 'Terminal_session::size_changed_sigh' RPC function registers a
signal handler that is triggered each time when the terminal size
changes. It enables the client to adjust itself to the new size by
subsequently calling the 'size' RPC function. Of all terminal servers,
only the graphical terminal triggers this signal.
AVL trees can't be copied with the default copy constructor as the
parent pointer of the first item of both of the resulting trees would
point to the original tree. Copying an AVL node, however, generally
violates the integrity of the corresponding tree. The copy constructor
of Avl_tree is used in some places but in those places it can be
replaced easily. So, this commit deletes the copy constructor of
Avl_node_base which makes Avl_node and Avl_tree non-copyable.
Issue #2654
The 'trace_logger' component can be used to easily gather, process and export
different types of tracing data. Which subjects to select is configurable via
session label policies and thread names. Which data to collect from the
selected subjects can be configured for each subject individually, for groups
of subjects, or for all subjects. The gathered data can be exported as log
output.
This is an example configuration of the 'trace_logger' component which shows
the default value for each attribute except the policy.thread and
policy.label:
! <config verbose="no"
! session_ram="10M"
! session_arg_buffer="4K"
! session_parent_levels="0"
! period_sec="5"
! activity="no"
! affinity="no"
! default_policy="null"
! default_buffer="4K">
!
! <policy label="init -> timer" />
! <policy label_suffix=" -> ram_fs" />
! <policy label_prefix="init -> encryption -> "
! thread="worker"
! buffer="4K"
! policy="null" />
! </config>
For more details see os/src/app/trace_logger/README.
Fixes#2654
Building this policy was disabled by a REQUIRES = riscv_toolchain_bugfix
to prevent compiler crashes on nightly test builds. Since the latest
RISCV toolchain update, test builds for RISCV crash at much more places
which makes this single work-around senseless.
Issue #2654
The 'Buffered_xml' utility is used by three components and a fourth is
on the way. To avoid another duplication of the code, this patch makes
it publicly available at 'os/buffered_xml.h'.
This patch replaces the 'Heap' by a 'Sliced_heap' to avoid the
allocation of a 16 KiB memory block when 'dummy' acts as a server. On
seL4, such an allocation would exceed the 1M quota as assigned by the
init.run script.
