Ensure that the timer does not handle timeouts again within 1000
microseconds after the last handling of timeouts. This makes denial of
service attacks harder. This commit does not limit the rate of timeout
signals handled inside the timer but it causes the timer to do it less
often. If a client continuously installs a very small timeout at the
timer it still causes a signal to be submitted to the timer each time
and some extra CPU time to be spent in the internal handling method. But
only every 1000 microseconds this internal handling causes user timeouts
to trigger.
If we would want to limit also the call of the internal handling method
to ensure that CPU time is spent beside the RPCs only every 1000
microseconds, things would get more complex. For instance, on NOVA
Time_source::schedule_timeout(0) must be called each time a new timeout
gets installed and becomes head of the scheduling queue. We cannot
simply overwrite the already running timeout with the new one.
Ref #2490
If the PIT timer driver gets activated too slow (e.g. because of a bad priority
configuration), it might miss counter wraps and would than produce sudden time
jumps. The driver now detects this problem dynamically, warns about it and
adapts the affected values to avoid time jumps.
Ref #2400
Add a "writeable" policy option to the ahci_drv and part_blk Block
servers and default from writeable to ready-only. Should a policy
permit write acesss the session request argument "writeable" may still
downgrade a session to ready-only.
Fix#2469
There are hardware timers whose frequency can't be expressed as
ticks-per-microsecond integer-value because only a ticks-per-millisecond
integer-value is precise enough. We don't want to use expensive
floating-point values here but nonetheless want to translate from ticks
to time with microseconds precision. Thus, we split the input in two and
translate both parts separately. This way, we can raise precision by
shifting the values to their optimal bit position. Afterwards, the results
are shifted back and merged together again.
As this algorithm is not so trivial anymore and used by at least three
timer drivers (base-hw/x86_64, base-hw/cortex_a9, timer/pit), move it to a
generic header to avoid redundancy.
Ref #2400
Due to the simplicity of the algorithm that translated from timer ticks
to time, we lost microseconds precision although the timer allows for it.
Ref #2400
As timer sessions are not expected to be microseconds precise (because
of RPC latency and scheduling), the session interface provided only a
method 'elapsed_ms' although the back end of this method in the timer
driver works with microseconds.
However, in some cases it makes sense to have a method 'elapsed_us'. The
values it returns might be milliseconds away from the "real" time but it
allows you to work with delays smaller than a millisecond without
getting a zero delta value.
This commit is motivated by the need for fast bursts of calibration
steps for the time interpolation in the new timer connection.
Ref #2400
The explicit relative location of the file instructed both target builds
to generate ../main.o which gloriously fails with parallel builds. The
produced range of error messages was astonishing ranging from "file
truncated" to "TLS reference in ../main.o mismatches non-TLS reference
in ../main.o".
This commit removes support for limitation of RAM allocations from the
platform_drv. A subsequent commit adds this feature to init.
Issue #2398
Issue #2407
Previously, the Genode::Timer::curr_time always used the
Timer_session::elapsed_ms RPC as back end. Now, Genode::Timer reads
this remote time only in a periodic fashion independently from the calls
to Genode::Timer::curr_time. If now one calls Genode::Timer::curr_time,
the function takes the last read remote time value and adapts it using
the timestamp difference since the remote-time read. The conversion
factor from timestamps to time is estimated on every remote-time read
using the last read remote-time value and the timestamp difference since
the last remote time read.
This commit also re-works the timeout test. The test now has two stages.
In the first stage, it tests fast polling of the
Genode::Timer::curr_time. This stage checks the error between locally
interpolated and timer-driver time as well as wether the locally
interpolated time is monotone and sufficiently homogeneous. In the
second stage several periodic and one-shot timeouts are scheduled at
once. This stage checks if the timeouts trigger sufficiently precise.
This commit adds the new Kernel::time syscall to base-hw. The syscall is
solely used by the Genode::Timer on base-hw as substitute for the
timestamp. This is because on ARM, the timestamp function uses the ARM
performance counter that stops counting when the WFI (wait for
interrupt) instruction is active. This instruction, however is used by
the base-hw idle contexts that get active when no user thread needs to
be scheduled. Thus, the ARM performance counter is not a good choice for
time interpolation and we use the kernel internal time instead.
With this commit, the timeout library becomes a basic library. That means
that it is linked against the LDSO which then provides it to the program it
serves. Furthermore, you can't use the timeout library anymore without the
LDSO because through the kernel-dependent LDSO make-files we can achieve a
kernel-dependent timeout implementation.
This commit introduces a structured Duration type that shall successively
replace the use of Microseconds, Milliseconds, and integer types for duration
values.
Open issues:
* The timeout test fails on Raspberry PI because of precision errors in the
first stage. However, this does not render the framework unusable in general
on the RPI but merely is an issue when speaking of microseconds precision.
* If we run on ARM with another Kernel than HW the timestamp speed may
continuously vary from almost 0 up to CPU speed. The Timer, however,
only uses interpolation if the timestamp speed remained stable (12.5%
tolerance) for at least 3 observation periods. Currently, one period is
100ms, so its 300ms. As long as this is not the case,
Timer_session::elapsed_ms is called instead.
Anyway, it might happen that the CPU load was stable for some time so
interpolation becomes active and now the timestamp speed drops. In the
worst case, we would now have 100ms of slowed down time. The bad thing
about it would be, that this also affects the timeout of the period.
Thus, it might "freeze" the local time for more than 100ms.
On the other hand, if the timestamp speed suddenly raises after some
stable time, interpolated time can get too fast. This would shorten the
period but nonetheless may result in drifting away into the far future.
Now we would have the problem that we can't deliver the real time
anymore until it has caught up because the output of Timer::curr_time
shall be monotone. So, effectively local time might "freeze" again for
more than 100ms.
It would be a solution to not use the Trace::timestamp on ARM w/o HW but
a function whose return value causes the Timer to never use
interpolation because of its stability policy.
Fixes#2400
Removes the following Fiasco.OC specific features:
* GDB extensions for Fiasco.OC
* i.MX53 support for Fiasco.OC
* Kernel debugger terminal driver
* Obsolete interface Native_pd
* Obsolete function of interface Native_cpu
This patch reduces the number of exception types by facilitating
globally defined exceptions for common usage patterns shared by most
services. In particular, RPC functions that demand a session-resource
upgrade not longer reflect this condition via a session-specific
exception but via the 'Out_of_ram' or 'Out_of_caps' types.
Furthermore, the 'Parent::Service_denied', 'Parent::Unavailable',
'Root::Invalid_args', 'Root::Unavailable', 'Service::Invalid_args',
'Service::Unavailable', and 'Local_service::Factory::Denied' types have
been replaced by the single 'Service_denied' exception type defined in
'session/session.h'.
This consolidation eases the error handling (there are fewer exceptions
to handle), alleviates the need to convert exceptions along the
session-creation call chain, and avoids possible aliasing problems
(catching the wrong type with the same name but living in a different
scope).
This patch mirrors the accounting and trading scheme that Genode employs
for physical memory to the accounting of capability allocations.
Capability quotas must now be explicitly assigned to subsystems by
specifying a 'caps=<amount>' attribute to init's start nodes.
Analogously to RAM quotas, cap quotas can be traded between clients and
servers as part of the session protocol. The capability budget of each
component is maintained by the component's corresponding PD session at
core.
At the current stage, the accounting is applied to RPC capabilities,
signal-context capabilities, and dataspace capabilities. Capabilities
that are dynamically allocated via core's CPU and TRACE service are not
yet covered. Also, the capabilities allocated by resource multiplexers
outside of core (like nitpicker) must be accounted by the respective
servers, which is not covered yet.
If a component runs out of capabilities, core's PD service prints a
warning to the log. To observe the consumption of capabilities per
component in detail, the PD service is equipped with a diagnostic
mode, which can be enabled via the 'diag' attribute in the target
node of init's routing rules. E.g., the following route enables the
diagnostic mode for the PD session of the "timer" component:
<default-route>
<service name="PD" unscoped_label="timer">
<parent diag="yes"/>
</service>
...
</default-route>
For subsystems based on a sub-init instance, init can be configured
to report the capability-quota information of its subsystems by
adding the attribute 'child_caps="yes"' to init's '<report>'
config node. Init's own capability quota can be reported by adding
the attribute 'init_caps="yes"'.
Fixes#2398
This patch reworks the implementation of core's RAM service to make use
of the 'Session_object' and to remove the distinction between the
"metadata" quota and the managed RAM quota. With the new implementation,
the session implicitly allocates its metadata from its own account. So
there is not need to handle 'Out_of_metadata' and 'Quota_exceeded' via
different exceptions. Instead, the new version solely uses the
'Out_of_ram' exception.
Furthermore, the 'Allocator::Out_of_memory' exception has become an alias
for 'Out_of_ram', which simplifies the error handling.
Issue #2398
This patch makes use of the new 'Quota_transfer::Account' by the service
types in base/service.h and uses 'Quota_transfer' objects in
base/child.cc and init/server.cc.
Furthermore, it decouples the notion of an 'Async_service' from
'Child_service'. Init's 'Routed_service' is no longer a 'Child_service'
but is based on the new 'Async_service' instead.
With this patch in place, quota transfers do no longer implicitly use
'Ram_session_client' objects. So transfers can in principle originate
from component-local 'Ram_session_component' objects, e.g., as used by
noux. Therefore, this patch removes a strumbling block for turning noux
into a single threaded component in the future.
Issue #2398
This patch replaces the 'Parent::Quota_exceeded',
'Service::Quota_exceeded', and 'Root::Quota_exceeded' exceptions
by the single 'Insufficient_ram_quota' exception type.
Furthermore, the 'Parent' interface distinguished now between
'Out_of_ram' (the child's RAM is exhausted) from
'Insufficient_ram_quota' (the child's RAM donation does not suffice to
establish the session).
This eliminates ambiguities and removes the need to convert exception
types along the path of the session creation.
Issue #2398
This patch replaces the former use of size_t with the use of the
'Ram_quota' type to improve type safety (in particular to avoid
accidentally mixing up RAM quotas with cap quotas).
Issue #2398
This commit moves the headers residing in `repos/base/include/spec/*/drivers`
to `repos/base/include/drivers/defs` or repos/base/include/drivers/uart`
respectively. The first one contains definitions about board-specific MMIO
iand RAM addresses, or IRQ lines. While the latter contains device driver
code for UART devices. Those definitions are used by driver implementations
in `repos/base-hw`, `repos/os`, and `repos/dde-linux`, which now need to
include them more explicitely.
This work is a step in the direction of reducing 'SPEC' identifiers overall.
Ref #2403
This patch replaces the set-defaults command by a reset command, which
is needed to use the Lenovo x250 trackpoint. (original patch by
Christian Prochaska)
Ldso now does not automatically execute static constructors of the
binary and shared libraries the binary depends on. If static
construction is required (e.g., if a shared library with constructor is
used or a compilation unit contains global statics) the component needs
to execute the constructors explicitly in Component::construct() via
Genode::Env::exec_static_constructors().
In the case of libc components this is done by the libc startup code
(i.e., the Component::construct() implementation in the libc).
The loading of shared objects at runtime is not affected by this change
and constructors of those objects are executed immediately.
Fixes#2332
Transfer quota to the session local RAM session to react to the
Quota_exceeded exception properly.
The platform driver keeps a session local RAM session for each of its
clients that is used to allocate DMA memory. A client needs to transfer
some of its quota to the platform driver, which in return transfers this
quota to the session local RAM session. As it happens allocating memory
from a RAM session involves book keeping and in this case, where the
available quota in the session did not suffice and the request was only
a few KiB, the platform driver handled the exception wrongly and did not
transfer the quota.
This problem did not surface up to now because all drivers allocate DMA
memory in larger chunks and the book keeping overhead was of no
consequence as the initial quota transfer probably covered the overhead.
Fixes#2316.
This commit includes changes to the Nic::Session_component interface.
We now pass the entire env to the component instead of only ram, rm and
the ep because we need the env to open connections from within the
Session_component implemenation. So far only the cadence_gem driver
needs this, though.
Issue #2280.
This patch eliminates the need for a global allocator by passing the
parent-service registry as argument to the 'Slave::Policy' constructor.
Fixes#2269
This commit enables compile-time warnings displayed whenever a deprecated
API header is included, and adjusts the existing #include directives
accordingly.
Issue #1987
To better support non-blocking terminal components, let the
'Terminal::Session::write()' function return the number of bytes
actually written.
Fixes#2240
Merge the platform-specific files and classes (they merely aggregated
themselves) so that each platform provides merely one class
Sd_card::Driver. Also, the Sd_card::Driver_base class is introduced for
the generic parts of Sd_card::Driver.
Ref #2206
Most implementations use a Signal_handler now to acknowledge the packet
instead of waiting for the transfer completion. The exceptions to that are
the non-DMA implementations for RPI and PL180
Ref #2206
In addition to that we now busy wait, i.e. poll, for interrupts
instead of using the IRQ session. That is fine because interrupts
were only used while configuring the HDMI over I2C and are not used
while normal operation.
Issue #1987.
