In addition to now using the framework the playback is triggered by a
timer. For now it is a periodic timer that triggers every 11 ms which
is roughly the current Audio:out period (*).
The driver now also behaves like the other BSD Audio_out driver, i.e,
it always advances the play pointer. That is vital for the Audio_out
stack above the driver to work properly (e.g. the mixer).
(*) It stands to reason if it would be better to use the async ALSA
timer interface instead of using the Timer session.
Fixes#1892.
This driver uses the Usb session interface and provides a Block session
to its client. See _repos/os/src/drivers/usb_block/README' for more
information.
Fixes#1885.
Instead of only hardcoding "hw" read 'alsa_device' attribute from the
config node to determine the proper playback device. The default value
is still "hw" in case the attribute is not present.
Fixes#1884.
The driver might end up in an endless loop on systems that do not
contain an i8042 controller when probing the AUX interface. This
leads to busy looping and in the end to not annoucing the Input
service. Components that wait for the announcement of the service
will therefore hang as well.
Normally a service gets announced only if it is usable but in this
case this is inconvient because it renders all scenarios that use
the input_merger non working on x86 systems that only provide USB
input and do not have PS/2 at all.
Ideally, the PS/2 driver should only be started if the system needs it.
That is currently not feasible and for the time being we post-pone the
inevitable and back down after several unsucessful attempts to read
from the AUX interface while initializing the driver.
Fixes#1871.
Now, the right PCI bus:device:function (BDF) is reported to the kernel
during assign_pci syscall - beforehand it was ever 0:0.0. The BDF is
needed to lookup the correct DMAR unit the kernel has to configure. This
was revealed as the DMAR unit for Intel graphics on x201 is not the same
as for all other PCI devices we have drivers for on this platform.
Fixes#1848
Move ADMA2 stuff to extra header and unit. Move ESDHCv2 implementations to
extra unit. Use exceptions instead of error codes. Clean-up documentation.
Ref #1497
The manual termination of multi-block writes via "Stop Transmission" commands
seems to leave the card in a busy state sometimes. This causes errors on
subsequent commands. Thus, we have to synchronize manually with the
card-internal state via "Send State" commands. Additionally, the method
for issuing the manual "Stop Transmission" commands was refined.
Ref #1497
We have to issue a data synchronization barrier after writing a ADMA2
table to ensure that the corresponding write commands were actually
executed before issuing the SD command.
Ref #1497
On i.MX53 QSB, a "Send Op Cond" command during the driver initialization
returns another response value than on the USB Armory. As the check for
this response seems to have no relevance for the driver functionality (Linux
reads the value from MMIO but I can't find a place in the source code where
it is used), we simply remove it.
Ref #1497
Previously, it was not necessary to acknowledge an IRQ initially before using
it. However, since the IRQ framework changed lately it is. Adapt to this.
Ref #1497
* use '_dma_ext' or '_fdpma' commands
* handle interrupts depending on mode of operation
* spelling fixes
* move ATA 'Idendity' struct to ata header
issue #1734
Destroying an object within the scope of a lambda/functor executed
in the object pool's apply function leads potentially to memory corruption.
Within the scope the corresponding object is locked and unlocked when
leaving the scope. Therefore, it is illegal to free the object's memory meanwhile.
This commit eliminates several places in core that destroyed wrongly in
the object pool's scope.
Fix#1713
Instead of holding SPEC-variable dependent files and directories inline
within the repository structure, move them into 'spec' subdirectories
at the corresponding levels, e.g.:
repos/base/include/spec
repos/base/mk/spec
repos/base/lib/mk/spec
repos/base/src/core/spec
...
Moreover, this commit removes the 'platform' directories. That term was
used in an overloaded sense. All SPEC-relative 'platform' directories are
now named 'spec'. Other files, like for instance those related to the
kernel/architecture specific startup library, where moved from 'platform'
directories to explicit, more meaningful places like e.g.: 'src/lib/startup'.
Fix#1673
