If the attribute 'interface' is not set in a 'domain' tag, the router tries to
dynamically receive and maintain an IP configuration for that domain by using
DHCP in the client role at all interfaces that connect to the domain. In the
DHCP discover phase, the router simply chooses the first DHCP offer that
arrives. So, no comparison of different DHCP offers is done. In the DHCP
request phase, the server is expected to provide an IP address, a gateway, a
subnet mask, and an IP lease time to the router. If anything substantial goes
wrong during a DHCP exchange, the router discards the outcome of the exchange
and goes back to the DHCP discover phase. At any time where there is no valid
IP configuration present at a domain, the domain does only act as DHCP client
and all other router functionality is disabled for the domain. A domain cannot
act as DHCP client and DHCP server at once. So, a 'domain' tag must either
have an 'interface' attribute or must not contain a 'dhcp-server' tag.
Ref #2534
An IPv4 config (for a domain/interface of the router) consists of
an IPv4 address, a subnet prefix specifier, an optional gateway
IPv4 address, and some flags that declare whether these fields and
the config as a whole are valid. To make the handling of those
tightly connected values easier and less error prone, we encapsulate
them in a new class.
Ref #2534
This was an error output-line for each affected packet previously but it
is pretty normal for the router to receive packets whose network layer
protocol it doesn't know . In the default case, these packets shall be
ignored silently.
Ref #2490
One can configure the NIC router to act as DHCP server at interfaces of a
domain by adding the <dhcp> tag to the configuration of the domain like
this:
<domain name="vbox" interface="10.0.1.1/24">
<dhcp-server ip_first="10.0.1.80"
ip_last="10.0.1.100"
ip_lease_time_sec="3600"
dns_server="10.0.0.2"/>
...
</domain>
The attributes ip_first and ip_last define the available IPv4 address
range while ip_lease_time_sec defines the lifetime of an IPv4 address
assignment in seconds. The IPv4 address range must be in the subnet
defined by the interface attribute of the domain tag and must not cover
the IPv4 address in this attribute. The dns_server attribute gives the
IPv4 address of the DNS server that might also be in another subnet.
The lifetime of an offered assignment is the configured round trip time of
the router while the ip_lease_time_sec is applied only if the offer is
requested by the client in time.
The ports/run/virtualbox_nic_router.run script is an example of how to
use the new DHCP server functionality.
Ref #2490
Previously, garbage collect was only done when an incoming packet passed the
Ethernet checks. Now it is really done first when receiving a packet at an
interface.
Ref #2490
If the router has no gateway attribute for a domain (means that the router
itself is the gateway), and it gets an ARP request for a foreign IP, it shall
answer with its own IP.
Ref #2490
Apply the style rule that an accessor is named similar to the the underlying
value. Provide read and write accessors for each mandatory header attribute.
Fix some incorrect structure in the headers like with the flags field
in Ipv4_packet.
Ref #2490
Encapsulate the enum into a struct so that it is named
Ethernet_frame::Type::Enum, give it the correct storage type
uint16_t, and remove those values that are (AFAIK) not used by
now (genode, world).
Ref #2490
Do not stop routing if the transport layer protocol is unknown but
continue with trying IP routing instead. The latter was already
done when no transport routing could be applied but for unknown transport
protocols we caught the exception at the wrong place.
Ref #2490
Previously, the Genode::Timer::curr_time always used the
Timer_session::elapsed_ms RPC as back end. Now, Genode::Timer reads
this remote time only in a periodic fashion independently from the calls
to Genode::Timer::curr_time. If now one calls Genode::Timer::curr_time,
the function takes the last read remote time value and adapts it using
the timestamp difference since the remote-time read. The conversion
factor from timestamps to time is estimated on every remote-time read
using the last read remote-time value and the timestamp difference since
the last remote time read.
This commit also re-works the timeout test. The test now has two stages.
In the first stage, it tests fast polling of the
Genode::Timer::curr_time. This stage checks the error between locally
interpolated and timer-driver time as well as wether the locally
interpolated time is monotone and sufficiently homogeneous. In the
second stage several periodic and one-shot timeouts are scheduled at
once. This stage checks if the timeouts trigger sufficiently precise.
This commit adds the new Kernel::time syscall to base-hw. The syscall is
solely used by the Genode::Timer on base-hw as substitute for the
timestamp. This is because on ARM, the timestamp function uses the ARM
performance counter that stops counting when the WFI (wait for
interrupt) instruction is active. This instruction, however is used by
the base-hw idle contexts that get active when no user thread needs to
be scheduled. Thus, the ARM performance counter is not a good choice for
time interpolation and we use the kernel internal time instead.
With this commit, the timeout library becomes a basic library. That means
that it is linked against the LDSO which then provides it to the program it
serves. Furthermore, you can't use the timeout library anymore without the
LDSO because through the kernel-dependent LDSO make-files we can achieve a
kernel-dependent timeout implementation.
This commit introduces a structured Duration type that shall successively
replace the use of Microseconds, Milliseconds, and integer types for duration
values.
Open issues:
* The timeout test fails on Raspberry PI because of precision errors in the
first stage. However, this does not render the framework unusable in general
on the RPI but merely is an issue when speaking of microseconds precision.
* If we run on ARM with another Kernel than HW the timestamp speed may
continuously vary from almost 0 up to CPU speed. The Timer, however,
only uses interpolation if the timestamp speed remained stable (12.5%
tolerance) for at least 3 observation periods. Currently, one period is
100ms, so its 300ms. As long as this is not the case,
Timer_session::elapsed_ms is called instead.
Anyway, it might happen that the CPU load was stable for some time so
interpolation becomes active and now the timestamp speed drops. In the
worst case, we would now have 100ms of slowed down time. The bad thing
about it would be, that this also affects the timeout of the period.
Thus, it might "freeze" the local time for more than 100ms.
On the other hand, if the timestamp speed suddenly raises after some
stable time, interpolated time can get too fast. This would shorten the
period but nonetheless may result in drifting away into the far future.
Now we would have the problem that we can't deliver the real time
anymore until it has caught up because the output of Timer::curr_time
shall be monotone. So, effectively local time might "freeze" again for
more than 100ms.
It would be a solution to not use the Trace::timestamp on ARM w/o HW but
a function whose return value causes the Timer to never use
interpolation because of its stability policy.
Fixes#2400
Previously, if a packet should be routed to a domain that had no interface
connected, the NIC router only printed "Unroutable packet". Technically,
this was wrong as an unavailable interface doesn't mean that the routing
failed. Now it gives an error "no interface connected to domain".
Ref #2193
The nic_router component can be used to individually route IPv4 packets
between multiple NIC sessions. Thereby, it can translate between
different IP subnets. The component supports port forwarding, as well as
the partitioning of the TCP and UDP port spaces.
Fixes#114
